Epiroc: Right here, right now

January 16, 2020

The 777 zinc-copper mine in Flin Flon, Manitoba is on the wane. After 15 years in  production, the underground operation is expected to close in 2022 unless Hudbay Minerals discovers more ore. In order to keep the doors open as long as possible, the Toronto-based company is trying to find efficiencies to enhance the viability of the operation.

One way to boost efficiency is to increase mucking intensity, or the number of hours spent actually moving ore, while reducing variability in the number of buckets mucked per stope per shift. During 2018, some shifts underperformed from a perspective of number of buckets mucked to target while others exceeded for an average of 56 buckets per stope.

To address this challenge, Hudbay launched a three-month pilot project in partnership with Epiroc in December 2018 to determine whether Mobilaris Mining Intelligence (MMI), a digital technology designed to track people and assets in real time, could make a difference. And it did.

Using MMI to track equipment from 25 access points at the test level increased the mucking rate by seven percent because equipment such as Epiroc’s Scooptram ST14 underground loader could be located instantly at the start of a shift and priorities adjusted during the shift to better match the company’s targets.

“Sometimes operators are pulled out of the stopes to do other tasks,” said production coordinator Nathan Steuart from the surface. “Now, we can track the actual hours allocated to production and if it’s more important for an operator to be back at the stope, we can instruct them to do that.”

Steuart, who grew up in Flin Flon, directs the crews from his simple 2-monitor workstation at the center of a one-story mine office perched on the volcanics of the Flin Flon-Snow Lake greenstone belt. One monitor shows a map of the mine levels and access points, while the other displays information about each piece of equipment as it passes an access point, most importantly location.

“The pilot was an opportunity to try some technology we knew was out there and to gain some efficiencies,” said mine manager Bob MacDonald on a phone-in from Sudbury to the 777 mine site. “We now have more consistency in the plans for our crews.”

In a broader sense, MMI is helping Hudbay apply Short Interval Control (SIC), a means of keeping a process – in this case mucking – on target by reducing variation. Typically in underground mining, managers must wait until the end of a shift to assess the difference between their target production and the actual tons of ore mucked. Any losses during the shift cannot be recovered.

The beauty of MMI is that it can signal if mucking intensity is underperforming during the shift so adjustments can be made right away. For example, if one stope is ahead of target and another is behind, Steuart can reassign the mucking fleet to keep both stopes on target.

The data generated in the process is like gold to Hudbay’s Manager of Technology Development Mike Jankowski.

“I’ve been able to see the value that Mobilaris Mining Intelligence brings from an  information management perspective,” the Torontobased electronics engineer said. “We now have the information we need to know whether a problem is worth addressing or not.”

The data also helps Steuart accurately predict how many buckets will be mucked under various scenarios. In the best-case scenario – a dayshift with an early bird component and an available fuel truck – operators can muck 11 buckets per hour.

“There was a bit of a learning curve for us, but we like what we got out of MMI, and there are plans to roll out the deployment to other areas of the mine,” said Steuart. Hudbay is also planning to install Mobilaris at Lalor, its gold-zinc mine about 210 kilometers to the east.

Source

Related Articles


Changing Scene

  • Intralec Announces Leadership Transition in Northern GTA Sales Region

    Intralec Announces Leadership Transition in Northern GTA Sales Region

    Intralec has announced an upcoming leadership transition as Cameron Slade, currently Warehouse Supervisor, steps into the role of Outside Sales Representative for the Northern GTA region and North Ontario. Cameron will be filling in for Beverly Pisco, who will be beginning her maternity leave this June. Cameron brings a strong foundation in the electrical industry,… Read More…

  • Specialized Power Solutions Welcomes Jonathan Udy as New Sales Manager

    Specialized Power Solutions Welcomes Jonathan Udy as New Sales Manager

    Specialized Power Solutions is excited to welcome Jonathan Udy to their team! Jonathan joins Specialized Power Solutions with over a decade of experience in the electrical industry, beginning his career as a Journeyman Electrician working across commercial and industrial projects. He later transitioned into power distribution sales with ABB, where he spent over six years… Read More…


Sponsored Content
The Easy Way to the Industrial IoT

The way to the Industrial IoT does not have to be complicated. Whether access to valuable data is required or new, data-driven services are to be generated, Weidmuller enables its customers to go from data to value the easy way. Weidmuller’s comprehensive and cutting-edge IIoT portfolio applies to greenfield and brownfield applications. Weidmuller offers components and solutions from data acquisition, data pre-processing, data communication and data analysis.

Visit Weidmuller’s Industrial IoT Portfolio.


ADVANCED Motion Controls Takes Servo Drives to New Heights (and Depths) with FlexPro Extended Environment Product Line

Advanced Motion Controls is proud to announce the addition of six new CANopen servo drives with Extended Environment capabilities to their FlexPro line. These new drives join AMC’s existing EtherCAT Extended Environment FlexPro drives, making the FlexPro line the go-to solution for motion control applications in harsh environments.

Many motion control applications take place in conditions that are less than ideal, such as extreme temperatures, high and low pressures, shocks and vibrations, and contamination. Electronics, including servo drives, can malfunction or sustain permanent damage in these conditions.

Read More


Service Wire Co. Announces New Titles for Key Executives

Bruce Kesler and Mark Gatewood have been given new titles and responsibilities for Service Wire Co.

Bruce Kesler has assumed the role of Senior Director – Business Development. Bruce will be responsible for Service Wire’s largest strategic accounts and our growing Strategic Accounts Team.

Mark Gatewood has been promoted to the role of Vice President – Sales & Marketing. In this role, Gatewood will lead the efforts of Service Wire Company’s entire sales and marketing organization in all market verticals.

Read More


Tri-Mach Announces the Purchase of an Additional 45,000 sq ft. Facility

Tri-Mach Elmira Facility

Recently, Tri-Mach Inc. was thrilled to announce the addition of a new 45,000 sq ft. facility. Located at 285 Union St., Elmira, ON, this facility expands Tri-Mach’s capabilities, allowing them to better serve the growing needs of their customers.

Positioning for growth, this additional facility will allow Tri-Mach to continue taking on large-scale projects, enhance product performance testing, and provide equipment storage for their customers. The building will also be the new home to their Skilled Trades Centre of Excellence.

Read More


JMP Parent Company, CONVERGIX Acquires AGR Automation, Expanding Global Reach

Convergix Automation Solutions has completed the acquisition of AGR Automation (“AGR”), a UK-based provider of custom, high-performance automation design and systems integration primarily to the life sciences industry.

Following Convergix’s acquisitions of JMP Solutions in August 2021 and Classic Design in February 2022, AGR marks the third investment in Crestview’s strategy to build Convergix into a diversified automation solutions provider targeting the global $500+ billion market, with a particular focus on the $70 billion global systems integration and connectivity segments. Financial terms of the transaction were not disclosed.

Read More


Latest Articles

  • Festo: Machine Safety – Why It Matters & How to Achieve It

    Festo: Machine Safety – Why It Matters & How to Achieve It

    For OEMs, machine builders, engineers, and plant managers, machine safety is more than regulatory compliance; it’s a responsibility to workers, a commitment to customers, and a strategic advantage. Every machine on the factory floor has two sides: its potential to drive productivity, and its potential to cause harm. Striking the right balance between performance and… Read More…

  • What Does Being a Gold Level Rockwell System Integrator Mean for Actemium Canada Clients?

    What Does Being a Gold Level Rockwell System Integrator Mean for Actemium Canada Clients?

    What does being a Gold Level Rockwell System Integrator mean to Actemium Canada clients? The obvious answer is that Actemium Canada brings a high level of expertise, knowledge, and experience to every project. But it also means added value in ways many people may not realize, including cost savings on hardware and an extended 3-year… Read More…